Відео

Worst video ever

Its very helpfull for me. Thank you

Thats not a "regular allen key" sir...thats a British one.

Thank you so much

Rubber doesnt like oil as it can deteriorate to a soft blob sometimes depending its origin

Omfg 🎉 thank 🎉 😢😢😢😢 I was worried I screwed it up during assembling it. So glad I looked at this. ❤ A very happy Aussie

He looks like Dan Morgan

I have the same machine but one of the plastic foot plates has broken ,where can I get a replacement part as cheap as possible

Great video! Thanks

I did this but heard all the dust, make sure to clean Belt first…I cleaned it with a towel method then redid the lubricant…all good

Thank you so much! Simple and right to the point!

How do you reset the lube sign/light to go off after oiling the treadmill?

Thank you sir!

That was pretty useless information mate

I get it in line but then when I go on it it always goes to the right

Good demo. Remind users that the straps on the clogs are to stop you going off the end at the finish - in a shell we use left/right pressure to balance the boat. In a coxless shell the right clog can be swivelled to steer.The bungee and the slope of the slide assist recovery forwards with your own momentum. However hooking on the straps can cause shin cramps on a long session. The action should be like a snatch in weightlifting when gravity aids recovery- in rowing.let the design of the Concept 2 do the work

da best! ❤

Hands at shoulder height …. Then all the video following shows hands at allow level. Clueless

What happens if I read the instructions wrong and I unscrewed both of the bolts completly and now I can’t get it to work properly. It makes a lot of noise and the belt is bunching to one side. I can’t use it at all. Please help 🙂

What's this like compared to your Slim-line treadmill? It has incline but otherwise seems kinda similar, except less programs and a less powerful motor?

Wd-40 work?

this video truly helped me. I have a walking pad and I was able to adjust it accordingly

Thank you!

Useful video, but doesn't explain how to reset flashing "Lube" on display panel.

Good morning hi have an old JTX model T100 I require a new power supply (7.5v-1.5amp) are you able to supply please.

My crosswalk stop running how can I make it run again?

Thank you sir you are great person 😅😅😅

Just polishing basically 😂😂

Trying this tomorrow. The book doesn’t say anything about adjusting small and waiting

I feel like an idiot as I've yet to figure out how to even use the bottle that came with my machine. Thought all I had to do was remove the silver foil inside the lid but nothing is coming out and it seems to have a solid felt seal. I think the instructions are talking about som self lubricating thing I'm meant to refill but its a very bad transaltion.

Thank so much for your help

Thank you for this. I tried to adjust the tension of my treadmill's belt and the manual that came with the treadmill did not seem to make sense at all. It said to move one screw clockwise while moving the other counterclockwise. I watched your video and you confirmed my suspicion. Thank you for that!

I may be over thinking this. Seems to me that adjusting the tightness of the belt while the machine is running has the potential of causing the belt to move off center again. The time it can take to move from one side to the other and then find the adjusting acres in the hole is typically long enough for the belt to move toward its new centered position. I'd recommend stopping the belt, adjust both sides and then start the belt again.

Thanks JTX - super helpful for my second hand spin bike which needed a lot of TLC. Thank you!

You are my hero😅😅

Thanks mate =)

Absolutely superb explanation on how to adjust the running belt on my Kayoba treadmill. Thank you.

Thank you for explaining what tightening and loosening the two sides of the belt actually does. The manual was not clear on that, and simple understanding helped me fix it, so thank you.

Well done video. Thank you

3:35 thats awfuly ALOT of lubricant. 3 syringes would make the oil drip... wont they?

Thanks!

Can’t decide between this and the Proform L6 both the same price.

Can you please recommend a brand or a name of the gel you’re using? I don’t want to get something that will be wrong for my treadmill or dangerous for me to use? Where can I buy it? Can I get one online?

Your videos are very very helpful thank you so much!

Where can I find this nstructions for the SPRINT 8?? We are really struggling. The enclosed instructions are abysmal

I have black lord motorised treadmill user manual how i can put oil inside?

Absolute legend ❤

Beautiful explanation. Really appreciate your effort in putting up this video

Promo sm ☺️

Easy, fast, useful and not in Chinese. Good job